Products

About Us

Knowledge Center

Accessories

Terms of Use

Featured Products

Site Map

Videos

Contact Us

Solenoid Control Electronics


Please use the following comparison table to find the product that meets your requirements.
Item Number Series Input Signal Controller Driver Power Supply Number of Devices
1

 

Pick and Hold Module

Requires External Pulse Input - Yes External Up to 2

The Pick and Hold Solenoid Driver Module is designed to avoid over heating of the solenoid coil once it is energized.

This product has been featured on Sensors Online and Product Design & Development.


Item Number Series Input Signal Controller Driver Power Supply Number of Devices
2

 

PWM Module

  0-5 VDC Input Signal - Yes External Up to 2
 0-10 VDC Input Signal
4-20 milliamps Input Signal
Step and Direction Input Signals
Quadrature Input Signals
External Potentiometer
Onboard Potentiometer
Proportional Joystick

The PWM Module is designed to enable the user to vary the voltage across a solenoid or other devices. The PWM output voltage is proportional to the input control voltage.


Item Number Series Input Signal Controller Driver Power Supply Number of Devices
3

 

Closed Loop Solenoid Process Control Module

 0-5 VDC Input Signal

- Yes External 1
0-10 VDC Input Signal
Phase-A and Phase-B Quadratue Signals
Step and Direction
0-20 milliamps Input Signal
External Potentiometer

This module offers a very low cost solution for limited angle / stroke position control.

The Closed Loop Solenoid Process Control Module is designed to control the position of a solenoid plunger / shaft, voice coil motor or similar devices.


Item Number Series Input Signal Controller Driver Power Supply Number of Devices
4

 

Pick and Drop Module

Requires External Trigger Input - Yes External Up to 2

The Pick and Drop Driver Module applies a single pulse to the device, then drops the supply voltage to zero.


Item Number Series Input Signal Controller Driver Power Supply Number of Devices
5

 

Load On-Off Power Cycling Module

 Not Required Built-in Signal Generator Yes External Up to 2

The Load On-Off Cycling Module is designed to enable the user to cycle the voltage across a solenoid or other devices.

The frequency of actuation, the output peak voltage. and the duty cycle of the actuation (ratio of on time to the length of one full cycle) are adjusted using the onboard potentiometer.


Item Number Series Input Signal Controller Driver Power Supply Number of Devices
6

 

Dual Proportional Valve Controller

- Open Loop

- Closed Loop

- Yes External Up to 2

 


Item Number Series Input Signal Controller Driver Power Supply Number of Devices
7

 

Serially Controlled Solenoid Driver Externally Controlled  Yes Yes External Up to 2

The solenoid control card is an easy-to-use, plug-and-play and cost effective solution for single or dual device solenoid control applications. It may be used as a stand-alone unit or may be commanded by an external device.


Item Number Series Input Signal Controller Driver Power Supply Number of Devices
8

 

Solenoid Commander Card Externally Controlled

Stand-alone

 

Yes - External Up to 24

 


Item Number Series Input Signal Controller Driver Power Supply Number of Devices
9

 

Solenoid Control Module

 

Externally Controlled

Stand-alone

 

Yes Yes External Up to 16

The compact and stand-alone unit consists of controller and the drivers.


Item Number Series Input Signal Controller Driver Power Supply Number of Devices
10

 

Solenoid Control System

Externally Controlled

Stand-alone

 

Yes Yes Built-in Up to 32

The compact and stand-alone unit consists of controller,  drivers and the power supplies.


Item Number Series Input Signal Controller Driver Power Supply Number of Devices
11

 

Tubular Solenoids

Open Frame Solenoids

Low Profile Solenoids

Hinged Clapper Solenoids

Latching Solenoids

Rotary Solenoids

         

 


Item Number Series Input Signal Controller Driver Power Supply Number of Devices
12

 

DIN Rail Mount Bracket -  - - - -

The bracket is used to mount our solenoid drivers to a DIN rail.


Item Number Series Input Signal Controller Driver Power Supply Number of Devices
13

 

Two-axis Joystick -  - - - -

 


Item Number Series Input Signal Controller Driver Power Supply Number of Devices
14

 

Three-axis Joystick -  - - - -

 


Item Number Series Input Signal Controller Driver Power Supply Number of Devices
15

 

Trackball -  - - - -

 

 

The compact and stand-alone unit consists of controller,  drivers and the power supplies.

Share this page:

 

Home | Products | Accessories | Knowledge Center | About Us | Terms of Use |Testimonials | Featured Products |Site Map | Videos | Contact Us