|
| |
Solenoid Control Electronics
|
Please use the
following comparison table to find the product that meets your requirements.
|
|
Item Number
|
Series
|
Input Signal
|
Controller
|
Driver
|
Power Supply
|
Number of Devices
|
|
1
|
Pick and Hold Module
|
Requires External Pulse Input
|
-
|
Yes
|
External
|
Up
to 2
|
|
The Pick and Hold Solenoid Driver Module is designed to avoid over
heating of the solenoid coil once it is energized.
This product has been
featured on Sensors Online and
Product Design & Development.
|
|
|
Item Number
|
Series
|
Input Signal
|
Controller
|
Driver
|
Power Supply
|
Number of Devices
|
|
2
|
PWM Module
|
0-5 VDC Input Signal
|
-
|
Yes
|
External
|
Up
to 2
|
|
0-10 VDC Input Signal
|
|
4-20 milliamps Input Signal
|
|
Step and Direction Input Signals
|
|
Quadrature Input Signals
|
|
External Potentiometer
|
|
Onboard Potentiometer
|
|
Proportional Joystick
|
|
The PWM Module is designed to enable the user to vary the voltage across
a solenoid or other devices.
The PWM
output voltage is proportional to the input control voltage.
|
|
|
Item Number
|
Series
|
Input Signal
|
Controller
|
Driver
|
Power Supply
|
Number of Devices
|
|
4
|
Closed
Loop Solenoid Process Control Module
|
0-5 VDC Input Signal
|
-
|
Yes
|
External
|
1
|
|
0-10 VDC Input Signal
|
|
Phase-A and
Phase-B Quadratue Signals
|
|
Step and
Direction
|
|
0-20
milliamps Input Signal
|
|
External Potentiometer
|
|
This module offers a very low cost solution for limited angle / stroke
position control.
The Closed Loop Solenoid Process Control Module is designed to control
the position of a solenoid plunger / shaft, voice coil motor or similar
devices.
|
|
|
Item Number
|
Series
|
Input Signal
|
Controller
|
Driver
|
Power Supply
|
Number of Devices
|
|
5
|
Pick and Drop Module
|
Requires External Trigger Input
|
-
|
Yes
|
External
|
Up
to 2
|
|
The
Pick and Drop Driver Module applies a single pulse to the device, then
drops the supply voltage to zero.
|
|
|
|
Item Number
|
Series
|
Input Signal
|
Controller
|
Driver
|
Power Supply
|
Number of Devices
|
|
6
|
Load On-Off Power
Cycling Module
|
Not
Required
|
Built-in Signal Generator
|
Yes
|
External
|
1
|
|
The Load On-Off Cycling Module is designed to enable the user to
cycle the voltage across a solenoid or other devices.
T
he
frequency of actuation, the output peak voltage. and the duty
cycle of the actuation (ratio of on time to the length of one
full cycle) are adjusted using the onboard potentiometer.
|
|
|
Item Number
|
Series
|
Input Signal
|
Controller
|
Driver
|
Power Supply
|
Number of Devices
|
|
8
|
Solenoid
Control Module
|
Externally Controlled
Stand-alone
|
Yes
|
Yes
|
External
|
Up
to 16
|
|
The compact and stand-alone unit consists of controller and the
drivers.
|
![]()
|
|
Item Number
|
Series
|
Input Signal
|
Controller
|
Driver
|
Power Supply
|
Number of Devices
|
|
9
|
Solenoid Control System
|
Externally Controlled
Stand-alone
|
Yes
|
Yes
|
Built-in
|
Up
to 32
|
|
The compact and stand-alone unit consists of controller,
drivers and the power supplies.
|
|
|
Item Number
|
Series
|
Input Signal
|
Controller
|
Driver
|
Power Supply
|
Number of Devices
|
|
11
|
DIN Rail Mount
Bracket
|
-
|
-
|
-
|
-
|
-
|
|
The bracket
is used to mount our solenoid drivers to a DIN rail.
|
|
|
Item Number
|
Series
|
Input Signal
|
Controller
|
Driver
|
Power Supply
|
Number of Devices
|
|
12
|
Two-axis Joystick
|
-
|
-
|
-
|
-
|
-
|
|
|
|
|
Item Number
|
Series
|
Input Signal
|
Controller
|
Driver
|
Power Supply
|
Number of Devices
|
|
13
|
Three-axis
Joystick
|
-
|
-
|
-
|
-
|
-
|
|
|
|
|
Item Number
|
Series
|
Input Signal
|
Controller
|
Driver
|
Power Supply
|
Number of Devices
|
|
14
|
Trackball
|
-
|
-
|
-
|
-
|
-
|
|
|
|
